Tools

A wide range of tools from engine stands to sockets and even a-frames. Please note: we do not accept any returns on tools or A-frames unless they are visibly faulty upon receipt!

Engine Stand

Bench mounted engine stand. Allows engine case to be rotated through 360-degrees. Can be used on gearboxes too.

5001

Engine Stand - mobile

Mobile engine stand - mounted on casters so you can whiz it around your garage! Quality brand.

5007A

Engine Dolly

Engine dolly. Heavy duty frame mounted on castors to easily move engines / gearboxes from under vehicles and around your garge.

5005

Flywheel Lock

Universal flywheel lock will fit 6v or 12v flywheels.

0111

Flywheel Pin Jig

Flywheel dowel pin jig. Allows for correct positioning when drilling crankshafts and flywheels for 8 dowel pins.

0120

Flywheel Seal Installation Tool

Flywheel seal installation tool does not require the dowel pins to be removed.

0150

Cam Follower Clips

Cam follower clips allow you to hold the followers in the correct position when working on the cam, etc. Essential if you are going to re-use the existing camshaft.

0113

Distributor Drive Puller

Distributor drive shaft puller allows the easy removal of the shaft from the case.

0115

Oil Pump Puller

Oil pump puller easily and safely allows removal of the pump from the case without causing damage.

0112

Oil Piston Puller

Oil piston puller removes seized oil pressure relief valve pistons.

0117

Oil Filler Nut Tool

Oil filler nut tool - lug type - suited for occasional use. Fits 3/8" ratchet.

0139

Oil Filler Nut Tool

Oil filler nut tool - internally grips the inside - more suite for regular use.

5102

Cylinder Head Assembly Tool

Cylinder head assembly tool aids the fitting out of heads easily.

0129

Gearbox Drain Plug Socket

Gearbox drain plug socket. Suitable for 3/8" ratchets. This size socket is hardly ever supplied in socket sets! This also fits the A-arm bush on IRS cars.

0114

Gearbox Drain Plug Wrench

Gearbox drain plug wrench / allen key.

5785

Starter Motor Bush Puller

Easily remove the starter motor bush with this handy tool.

7062

Spring Plate Remover

Spring plate removal tool - ideal when lowering or adjusting the rear suspension on your Beetle / Ghia.

0116

Axle Nut Tool

Axle nut tool allows for easier removal of seized axle nuts. Apply extra pressure with a ratchet or bar and whack it with a hammer (no, we're not kidding). Available for 36mm nuts or 46mm nuts - specify when ordering.

0130

36mm Socket

36mm Socket - the size for flywheel gland nuts and Bug rear hub nuts. Available for 1/2" or 3/4" ratchets - specify size when ordering.

0002

Splined Socket

Splined socket for CV joint bolts. Fits 3/8" ratchet.

0135

Adjustable Push Rod

Adjustable push rod is useful when setting correct valve geometry on modified engines.

0119

Crankcase Spliiter

Crankcase splitter simply fits into the oil pump aperture and helps to split awkward cases open!

0121

Crankshaft Pulley Remover

Crankshaft pulley remover - can be used with the engine in place. Allows equal pressure on the pulley aiding removall.

0122

Crank Gear Puller

Crank gear puller tool.

0132

Clutch Alignement Tool

Clutch alignment tool - available for Types 1/2/3 or Type 4 engines - specify when ordering.

0143

Helping Hand Tool

Ideal for steadying drums or flywheels whilst loosening nuts, etc.

0145

Mr. Torque Tool

Multiplies leverage from a normal ratchet. For use on flywheel gland nuts and rear hub nuts. Supplied as a complete kit including drum plate, 6 volt gear and 12 volt gear.

0133

Airflow Meter

Airflow meter allows you to balance twin-carb setups.

0124

Airflow Meter Adapter

Airflow meter adapter will fit the above unit to allow use on either the 34ICT or Kadron/EMPI/Solex carbs - choose type when ordering.

0124A

Chamber Volume Tool

Measures the combustion chamber volume. Supplied with a syringe and 3 plexi-glass discs to fit most bore sizes.

0137

Deck Height Tool

Accurately measure the deck height with this tool and a set of feeler gauges (not included).

0126

Crankcase Measuring Tool

Handy tool for measuring crankcases. Pre-cut for various sizes.

0140G

Crankshaft Measuring Tool

Handy way to measure crankshaft size - pre-cut for the popular sizes.

0140K

Coil Spring Compressors

Coil spring compressors - for working on 1302/03 front strut assemblies or anything with macpherson struts. Supplied as a pair!

0127

A-Frame

A-Frame. Easy and simply way to tow your car around without an extra driver. Simply attach to the car being towed, hook-up to your tow-bar and away you go! Available for Beam-axle cars or 1302/03 cars - specify when ordering.

*** Please check the braked capacity of your tow car and the weight ratio of tow-car to towed-car. Also there are restrictions AGAINST the use of A-frames in some European countries. When buying one from us, we are assuming you are fully aware of the legalities of your setup and are compliant with all relevant laws ***

3127

End Float Tool

Use this tool to set the flywheel end float - used with a pair of feel gauges (not included)

0125